Ticket #2146: battery-discharging.dmesg

File battery-discharging.dmesg, 15.3 KB (added by nicolas.dufresne, 10 years ago)

Battery discharging after boot

Line 
1ery Table at 0x0039
2[21474537.610000] cfi_cmdset_0001: Erase suspend on write enabled
3[21474537.610000] erase region 0: offset=0x0,size=0x2000,blocks=8
4[21474537.610000] erase region 1: offset=0x10000,size=0x10000,blocks=31
5[21474537.610000] physmap-flash.0: 1 set(s) of 1 interleaved chips --> 4 partitions of 512 KiB
6[21474537.610000] RedBoot partition parsing not available
7[21474537.625000] S3C24XX NAND Driver, (c) 2004 Simtec Electronics
8[21474537.630000] s3c2440-nand s3c2440-nand: Tacls=1, 10ns Twrph0=3 30ns, Twrph1=2 20ns
9[21474537.630000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xaa (Samsung NAND 256MiB 1,8V 8-bit)
10[21474537.630000] Bad block table found at page 131008, version 0x01
11[21474537.630000] Bad block table found at page 130944, version 0x01
12[21474537.635000] nand_read_bbt: Bad block at 0x0b660000
13[21474537.635000] 6 cmdlinepart partitions found on MTD device neo1973-nand
14[21474537.635000] Creating 6 MTD partitions on "neo1973-nand":
15[21474537.635000] 0x00000000-0x00040000 : "u-boot"
16[21474537.645000] 0x00040000-0x00080000 : "u-boot_env"
17[21474537.655000] 0x00080000-0x00880000 : "kernel"
18[21474537.665000] 0x00880000-0x00920000 : "splash"
19[21474537.675000] 0x00920000-0x00960000 : "factory"
20[21474537.685000] 0x00960000-0x10000000 : "rootfs"
21[21474537.705000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
22[21474537.710000] s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
23[21474537.715000] s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
24[21474537.715000] s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
25[21474537.780000] usb usb1: configuration #1 chosen from 1 choice
26[21474537.785000] hub 1-0:1.0: USB hub found
27[21474537.785000] hub 1-0:1.0: 2 ports detected
28[21474537.800000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
29[21474537.800000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
30[21474537.800000] usb usb1: Product: S3C24XX OHCI
31[21474537.800000] usb usb1: Manufacturer: Linux 2.6.28-GTA02_andy-tracking_b6d34d41617a6315-mokodev ohci_hcd
32[21474537.800000] usb usb1: SerialNumber: s3c24xx
33[21474537.805000] usbcore: registered new interface driver cdc_acm
34[21474537.805000] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
35[21474537.805000] Initializing USB Mass Storage driver...
36[21474537.805000] usbcore: registered new interface driver usb-storage
37[21474537.805000] USB Mass Storage support registered.
38[21474537.810000] usbcore: registered new interface driver libusual
39[21474537.815000] usbcore: registered new interface driver usbserial
40[21474537.815000] USB Serial support registered for generic
41[21474537.820000] usbcore: registered new interface driver usbserial_generic
42[21474537.820000] usbserial: USB Serial Driver core
43[21474537.820000] USB Serial support registered for GSM modem (1-port)
44[21474537.825000] usbcore: registered new interface driver option
45[21474537.825000] option: v0.7.2:USB Driver for GSM modems
46[21474537.835000] s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes
47[21474537.835000] gta02_udc_command(2)
48[21474537.840000] g_ether gadget: using random self ethernet address
49[21474537.840000] g_ether gadget: using random host ethernet address
50[21474537.850000] usb0: MAC 4a:64:b2:e8:8e:e4
51[21474537.850000] usb0: HOST MAC ee:84:51:4a:e4:a2
52[21474537.850000] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
53[21474537.850000] g_ether gadget: g_ether ready
54[21474537.850000] gta02_udc_command(1)
55[21474537.855000] mice: PS/2 mouse device common for all mice
56[21474537.870000] i2c /dev entries driver
57[21474537.875000] s3c2440-i2c s3c2440-i2c: slave address 0x10
58[21474537.880000] s3c2440-i2c s3c2440-i2c: bus frequency set to 390 KHz
59[21474537.905000] pcf50633 0-0073: Probed device version 19 variant 132
60[21474537.960000] input: GTA02 PMU events as /class/input/input0
61[21474538.000000] pcf50633-rtc pcf50633-rtc: rtc core: registered pcf50633 as rtc0
62[21474538.035000] wake enabled for irq 53
63[21474538.045000] s3c2440-ts s3c2440-ts: Starting
64[21474538.045000]   Creating Median ts filter len 31 depth 2 dec 24
65[21474538.045000]   Created Mean ts filter len 8 thresh 18
66[21474538.045000] s3c2440-ts s3c2440-ts: 2 filter(s) initialized
67[21474538.045000] s3c2440-ts s3c2440-ts: successfully loaded
68[21474538.050000] input: s3c2410 TouchScreen as /class/input/input1
69[21474538.055000] pcf50633 0-0073: INT1=0x80 INT2=0x00 INT3=0x00 INT4=0x40 INT5=0x00
70[21474538.065000] pcf50633 0-0073: INT1=0x00 INT2=0x00 INT3=0x00 INT4=0x00 INT5=0x00
71[21474538.075000] pcf50633 0-0073: INT1=0x00 INT2=0x00 INT3=0x00 INT4=0x00 INT5=0x00
72[21474538.075000] neo1973-pm-host neo1973-pm-host.0: starting
73[21474538.080000] input: lis302-1 (top) as /class/input/input2
74[21474538.105000] lis302dl lis302dl.1: Found lis302-1 (top)
75[21474538.110000] input: lis302-2 (bottom) as /class/input/input3
76[21474538.140000] lis302dl lis302dl.2: Found lis302-2 (bottom)
77[21474538.145000] input: Neo1973 Buttons as /class/input/input4
78[21474538.185000] wake enabled for irq 48
79[21474538.185000] neo1973-resume neo1973-resume.0: starting
80[21474538.225000] s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
81[21474538.240000] APM Battery Driver
82[21474538.245000] bq27000-battery bq27000-battery.0: BQ27000 Battery Driver (C) 2008 Openmoko, Inc
83[21474538.260000] Bluetooth: Generic Bluetooth USB driver ver 0.3
84[21474538.260000] usbcore: registered new interface driver btusb
85[21474538.260000] cpuidle: using governor ladder
86[21474538.265000] sdhci: Secure Digital Host Controller Interface driver
87[21474538.265000] sdhci: Copyright(c) Pierre Ossman
88[21474538.270000] s3c2440-sdi s3c2440-sdi: host detect has no irq available
89[21474538.270000] mapped channel 0 to 0
90[21474538.275000] s3c2440-sdi s3c2440-sdi: powered down.
91[21474538.275000] s3c2440-sdi s3c2440-sdi: initialisation done.
92[21474538.280000] HIFInit
93[21474538.285000] Registered led device: neo1973:vibrator
94[21474538.295000] Registered led device: gta02-power:orange
95[21474538.300000] Registered led device: gta02-power:blue
96[21474538.300000] Registered led device: gta02-aux:red
97[21474538.350000] usbcore: registered new interface driver usbhid
98[21474538.350000] usbhid: v2.6:USB HID core driver
99[21474538.365000] logger: created 64K log 'log_main'
100[21474538.365000] logger: created 256K log 'log_events'
101[21474538.370000] logger: created 64K log 'log_radio'
102[21474538.380000] regulator: auto: 3300 mV normal
103[21474538.380000] regulator: down1: 1300 <--> 1600 mV normal
104[21474538.395000] regulator: down2: 1800 mV normal
105[21474538.395000] regulator: ldo1: 3300 <--> 1300 mV normal
106[21474538.410000] regulator: ldo2: 3300 mV normal
107[21474538.420000] regulator: ldo3: 3000 mV normal
108[21474538.430000] regulator: ldo4: 3200 mV normal
109[21474538.435000] neo1973-pm-bt neo1973-pm-bt.0: FIC Neo1973 Bluetooth Power Management: starting
110[21474538.485000] neo1973-pm-bt neo1973-pm-bt.0: GTA02 Set PCF50633 LDO4 = 3200
111[21474538.485000] s3c2440-sdi s3c2440-sdi: running at 0kHz (requested: 0kHz).
112[21474538.490000] s3c2440-sdi s3c2440-sdi: running at 196kHz (requested: 195kHz).
113[21474538.490000] s3c2440-sdi s3c2440-sdi: running at 196kHz (requested: 195kHz).
114[21474538.495000] s3c2440-sdi s3c2440-sdi: running at 196kHz (requested: 195kHz).
115[21474538.495000] s3c2440-sdi s3c2440-sdi: running at 196kHz (requested: 195kHz).
116[21474538.510000] regulator: ldo5: 3000 mV normal
117[21474538.515000] regulator: Unable to get requested regulator: RF_3V
118[21474538.515000] neo1973-pm-gps neo1973-pm-gps.0: FIC Neo1973 GPS Power Managerment:starting
119[21474538.515000] s3c2440-sdi s3c2440-sdi: running at 196kHz (requested: 195kHz).
120[21474538.525000] regulator: ldo6: 3000 mV normal
121[21474538.525000] regulator: hcldo: 2000 <--> 3300 mV fast
122[21474538.530000] mmc0: queuing CIS tuple 0x01 length 3
123[21474538.550000] Detected S-Media IRQ# pullup, enabling interrupt
124[21474538.550000] glamo3362 glamo3362.0: Glamo interrupt registered
125[21474538.555000] g_ether gadget: full speed config #1: CDC Ethernet (ECM)
126[21474538.570000] mmc0: queuing CIS tuple 0x1a length 5
127[21474538.575000] mmc0: queuing CIS tuple 0x1b length 8
128[21474538.575000] s3c2440-sdi s3c2440-sdi: running at 25000kHz (requested: 25000kHz).
129[21474538.575000] s3c2440-sdi s3c2440-sdi: running at 25000kHz (requested: 25000kHz).
130[21474538.580000] mmc0: queuing CIS tuple 0x80 length 1
131[21474538.580000] mmc0: queuing CIS tuple 0x81 length 1
132[21474538.585000] mmc0: queuing CIS tuple 0x82 length 1
133[21474538.585000] mmc0: new SDIO card at address 0001
134[21474538.595000] glamo3362 glamo3362.0: Glamo core PLL1: 49119232Hz, PLL2: 89980928Hz
135[21474538.665000] pcf50633 0-0073: INT1=0x80 INT2=0x00 INT3=0x00 INT4=0x40 INT5=0x00
136[21474538.685000] pcf50633 0-0073: INT1=0x00 INT2=0x00 INT3=0x00 INT4=0x00 INT5=0x00
137[21474538.685000] SMEDIA Glamo frame buffer driver (C) 2007 Openmoko, Inc.
138[21474538.750000] spin_lock_init
139[21474538.750000] glamofb_update_lcd_controller spin_lock_irqsave
140[21474538.750000] glamofb_update_lcd_controller spin_unlock_irqrestore
141[21474538.765000] pcf50633 0-0073: INT1=0x00 INT2=0x00 INT3=0x00 INT4=0x00 INT5=0x00
142[21474538.915000] fbcon_event_notify action=5, data=c781fa58
143[21474538.935000] glamofb_update_lcd_controller spin_lock_irqsave
144[21474538.935000] glamofb_update_lcd_controller spin_unlock_irqrestore
145[21474539.005000] Console: switching to colour frame buffer device 80x58
146[21474539.075000] fb0: SMedia Glamo frame buffer device
147[21474539.415000] BMI Get Target Info: Exit (ver: 0x20000059 type: 0x1)
148[21474539.470000] AR6000 Reg Code = 0x40000060
149[21474539.540000] glamo-spi-gpio glamo-spi-gpio.0: registering c048d734: jbt6k74
150[21474539.795000] usb 1-1: new full speed USB device using s3c2410-ohci and address 2
151[21474539.850000] Corgi Backlight Driver Initialized.
152[21474539.850000] glamo-mci glamo-mci.0: glamo_mci driver (C)2007 Openmoko, Inc
153[21474539.855000] glamo-mci glamo-mci.0: probe: mapped mci_base:c88a2400 irq:0.
154[21474539.855000] glamo-mci glamo-mci.0: ******* glamo_mci_reset
155[21474539.860000] glamo-mci glamo-mci.0: glamo_mci_set_ios: power down.
156[21474539.860000] glamo-mci glamo-mci.0: initialisation done.
157[21474539.865000] regulator: memldo: 1800 mV normal
158[21474539.865000] regulator_check_voltage: operation not allowed for hcldo
159[21474539.875000] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
160[21474539.880000] ASoC version 0.13.2
161[21474539.885000] WM8753 Audio Codec 0.16
162[21474539.890000] glamo-mci glamo-mci.0: powered (vdd = 20) clk: 0kHz div=255 (req: 0kHz). Bus width=0
163[21474539.895000] regulator_check_voltage: operation not allowed for hcldo
164[21474539.895000] SD power -> 3200mV
165[21474539.895000] glamo-mci glamo-mci.0: powered (vdd = 20) clk: 195kHz div=255 (req: 195kHz). Bus width=0
166[21474539.900000] glamo-mci glamo-mci.0: powered (vdd = 20) clk: 195kHz div=255 (req: 195kHz). Bus width=0
167[21474539.905000] glamo-mci glamo-mci.0: powered (vdd = 20) clk: 195kHz div=255 (req: 195kHz). Bus width=0
168[21474539.910000] glamo-mci glamo-mci.0: Error after cmd: 0x8120
169[21474539.915000] glamo-mci glamo-mci.0: Error after cmd: 0x120
170[21474539.925000] glamo-mci glamo-mci.0: Error after cmd: 0x8120
171[21474539.930000] glamo-mci glamo-mci.0: Error after cmd: 0x120
172[21474539.935000] regulator_check_voltage: operation not allowed for hcldo
173[21474539.945000] SD power -> 2700mV
174[21474539.950000] glamo-mci glamo-mci.0: powered (vdd = 15) clk: 195kHz div=255 (req: 195kHz). Bus width=0
175[21474539.960000] asoc: WM8753 HiFi <-> s3c24xx-i2s mapping ok
176[21474539.970000] asoc: WM8753 Voice <-> Bluetooth mapping ok
177[21474539.975000] glamo-mci glamo-mci.0: powered (vdd = 15) clk: 195kHz div=255 (req: 195kHz). Bus width=0
178[21474539.980000] glamo-mci glamo-mci.0: powered (vdd = 15) clk: 195kHz div=255 (req: 195kHz). Bus width=0
179[21474540.040000] usb 1-1: configuration #1 chosen from 1 choice
180[21474540.050000] glamo-mci glamo-mci.0: powered (vdd = 15) clk: 195kHz div=255 (req: 195kHz). Bus width=0
181[21474540.065000] glamo-mci glamo-mci.0: powered (vdd = 15) clk: 16666kHz div=2 (req: 16666kHz). Bus width=0
182[21474540.070000] glamo-mci glamo-mci.0: powered (vdd = 15) clk: 16666kHz div=2 (req: 16666kHz). Bus width=2
183[21474540.080000] mmc1: new SD card at address e624
184[21474540.095000] mmcblk0: mmc1:e624 SU512 483 MiB
185[21474540.100000]  mmcblk0: p1
186[21474540.150000] usb 1-1: New USB device found, idVendor=0a12, idProduct=0001
187[21474540.160000] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
188[21474540.200000] ALSA device list:
189[21474540.205000]   #0: neo1973-gta02 (WM8753)
190[21474540.215000] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
191[21474540.240000] TCP cubic registered
192[21474540.245000] NET: Registered protocol family 17
193[21474540.255000] Bridge firewalling registered
194[21474540.265000] Bluetooth: L2CAP ver 2.11
195[21474540.275000] Bluetooth: L2CAP socket layer initialized
196[21474540.280000] Bluetooth: SCO (Voice Link) ver 0.6
197[21474540.285000] Bluetooth: SCO socket layer initialized
198[21474540.295000] Bluetooth: RFCOMM socket layer initialized
199[21474540.300000] Bluetooth: RFCOMM TTY layer initialized
200[21474540.305000] Bluetooth: RFCOMM ver 1.10
201[21474540.310000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
202[21474540.315000] Bluetooth: BNEP filters: protocol multicast
203[21474540.320000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
204[21474540.355000] pcf50633-rtc pcf50633-rtc: hctosys: invalid date/time
205[21474542.920000] VFS: Mounted root (jffs2 filesystem).
206[21474542.925000] Freeing init memory: 152K
207[21474572.495000] udevd version 124 started
208[21474593.220000] FAT: invalid media value (0x00)
209[21474593.220000] VFS: Can't find a valid FAT filesystem on dev mmcblk0.
210[21474593.225000] VFS: Can't find ext4 filesystem on dev mmcblk0.
211[21474593.225000] EXT4-fs: Update your userspace programs to mount using ext4
212[21474593.225000] EXT4-fs: ext4dev backwards compatibility will go away by 2.6.31
213[21474593.230000] VFS: Can't find ext4 filesystem on dev mmcblk0.
214[21474593.235000] FAT: invalid media value (0x00)
215[21474593.235000] VFS: Can't find a valid FAT filesystem on dev mmcblk0.
216[21474597.740000] kjournald starting.  Commit interval 5 seconds
217[21474597.845000] EXT3 FS on mmcblk0p1, internal journal
218[21474597.845000] EXT3-fs: recovery complete.
219[21474597.910000] EXT3-fs: mounted filesystem with ordered data mode.
220[21474708.830000] glamofb_update_lcd_controller spin_lock_irqsave
221[21474708.830000] glamofb_update_lcd_controller spin_unlock_irqrestore
222[21474708.925000] glamofb_update_lcd_controller spin_lock_irqsave
223[21474708.925000] glamofb_update_lcd_controller spin_unlock_irqrestore
224[21474708.930000] fbcon_event_notify action=1, data=c6155e08
225[21474715.520000] pcf50633 0-0073: Masking IRQ 6
226[21474715.550000] pcf50633 0-0073: Unmasking IRQ 6
227[21474774.455000] fbcon_event_notify action=9, data=c6155e18
228[21474779.530000] fbcon_event_notify action=9, data=c6155e18
229[21474784.590000] fbcon_event_notify action=9, data=c6155e18
230[21474790.915000] modem wakeup interrupt
231[   21.705000] fbcon_event_notify action=12, data=c6155dd0
232[   21.880000] fbcon_event_notify action=9, data=c6155e18
233[   22.120000] pcf50633 0-0073: INT1=0x80 INT2=0x00 INT3=0x00 INT4=0x40 INT5=0x00
234[   22.130000] pcf50633 0-0073: INT1=0x00 INT2=0x00 INT3=0x00 INT4=0x00 INT5=0x00
235[   22.140000] pcf50633 0-0073: INT1=0x00 INT2=0x00 INT3=0x00 INT4=0x00 INT5=0x00
236[   51.895000] fbcon_event_notify action=9, data=c6155e18
237[   56.960000] fbcon_event_notify action=9, data=c6155e18
238[   62.025000] fbcon_event_notify action=9, data=c6155e18
239[  145.230000] JFFS2 notice: (1310) check_node_data: wrong data CRC in data node at 0x0ccf14cc: read 0xb0ba0578, calculated 0xdbda2e38.